建筑物掏土纠倾法单孔与多孔塑性区特性研究及工程应用

在建筑物水平掏土纠倾工程中，掏土孔间距是影响纠倾工程安全与工期的重要因素。为了快速准确地确定纠倾工程中的水平掏土孔间距，研究了单个掏土孔和多个掏土孔情况下孔周边土体塑性区发展特性。利用土体塑性力学分析计算得到了单孔下的孔周土塑性区半径，而后通过有限元模拟得到孔周土体塑性区半径的数值解，将孔周塑性区半径解析解与数值解进行了对比。并通过有限元数值模型研究了多个掏土孔相互影响情况下的塑性区发展规律，以孔间土体塑性区贯通时的距离作为掏土孔间距。考虑土体参数随机特性的影响，研究不同上部荷载作用下掏土孔间距的取值变化规律，上部面荷载与地基承载力特征值比值用p表示，孔间距与掏土孔直径比值用n表示。研究发现：多孔塑性区半径（孔间塑性区贯通时）是单孔塑性区半径的1.3倍左右;标准化荷载p与孔间距比值n二者呈线性关系;通过不同土体参数及上部荷载的不同情况下的p-n曲线，给出了掏土孔间距建议值。同时，将研究结果与三个实际工程进行对比，发现p-n曲线法与实际结果更为接近。     

配分工艺对中碳Ti-Mo高强Q&P钢组织和性能的影响

摘要：采用盐浴实验、扫描电镜、透射电镜、拉伸实验和磨损实验等手段，研究了配分工艺对中碳Ti Mo钢组织和性能的影响，分析了不同配分工艺处理下的组织演变和性能变化。结果表明，显微组织主要由回火马氏体、渗碳体、(Ti，Mo)C粒子组成。随着配分时间的延长和配分温度的升高，板条马氏体数量减少，马氏体板条厚度增加，边界钝化。此外，随着配分温度从310℃提高至400℃，抗拉强度、硬度和低温冲击韧性同时下降，分别降低约250MPa、56HV和15J。最后，Ms以下温度配分（310℃）试样的耐磨损性能明显优于Ms以上温度配分（400℃）试样。Ms以下温度配分试样磨损表面形貌以塑性变形为主，Ms以上温度配分试样磨损表面以犁沟为主。     

超高效液相色谱⁃四极杆⁃飞行时间质谱对含PET食品接触材料中可迁移非挥发性物质的筛查研究

采用超高效液相色谱⁃四极杆⁃飞行时间高分辨质谱（UPLC⁃Q⁃TOF）对4类不同类型的含聚对苯二甲酸乙二醇酯（PET）材质的食品接触材料在4 %乙酸和50 %乙醇模拟物中的迁移出的非挥发性未知物进行筛查解析。结果表明，产品在4 %乙酸模拟物的迁移风险远小于50 %乙醇模拟物，主要迁移物质为聚合单体形成的寡聚物，抗氧剂、润滑剂、胶黏剂等加工助剂以及生产加工、迁移过程中形成的非有意添加物（NIAS）物质；纯PET材质的产品迁移物质较少，多层复合材料迁移物质较多。复合材质的产品中，PET材质可能在生产时添加了己二酸、癸二酸、新戊二醇等物质，进行了改性处理；此外，部分迁移物质会与模拟物中的乙醇发生反应，生成新的NIAS物质。     

Electrochemical performance of in situ LiFePO4 modified by N-doped graphene for Li-ion batteries

LiFePO₄ modified by N-doped graphene (NG) with a three-dimensional conductive network structure was synthesized via a one-step in situ hydrothermal method. The effects of N amount of NG on the phase structure, morphology, and electrochemical properties of LiFePO₄ are investigated in this study. X-ray diffraction (XRD) results show that doping suitable N amounts in NG do not alter the crystal structure of LiFePO_4, and scanning electron microscopy (SEM) images show that NG can slightly reduce the particle size of LiFePO₄. The high-resolution transmission electron microscopy (HRTEM) results show that the LiFePO₄ particles are well covered and connected by NG. The electrochemical performance confirms that LiFePO₄ modified by 20% N-doped graphene (named LFP/NG-4) displays a perfect specific capacity of 166.6 mAh·g^?1 at a rate of 0.2C and can reach 125 mAh·g^?1 at a rate of 5 C. Electrochemical impedance spectroscopy (EIS) results illustrate that the charge transfer resistance value of the LFP/NG-4 composite is only 58.6 Ω, which is very low compared with LiFePO₄. Cyclic voltammetry (CV) tests indicate that the addition of 20% N-doped graphene can effectively reduce electrode polarization and improve reversibility. The LFP/NG-4 composite with a three-dimensional conductive network structure can be regarded as a promising cathode material for Li-ion batteries.     

Challenges and strategies of all-inorganic lead-free halide perovskite solar cells

Hybrid lead halide perovskite solar cells (PSCs) have experienced a rapid development in the past decade and a certified efficiency up to 25.5% has been achieved. However, the presence of toxic lead component and the inherent poor thermal stability of the organic cations in the hybrid lead halide perovskites obstruct the commercial applications of their corresponding photovoltaic devices. Therefore, fabricating high-efficient all-inorganic lead-free PSCs is a promising direction. This review summarizes the related research progress, which mainly focuses on the structural and optoelectronic properties of inorganic lead-free perovskites and devices. In particular, the strategies for improving the properties and stability of Cs–Sn perovskites, as well as enhancing the photovoltaic performance of the corresponding devices are highlighted. An outlook of challenges and future directions regarding to all-inorganic lead-free PSCs are also proposed.     

Synthesis and plasma treatment of nitrogen-doped graphene fibers for high-performance supercapacitors

Graphene fiber-based supercapacitor has aroused great interest as a flexible power source in future wearable electronics. However, the low electrochemical performance of graphene fibers (GFs) usually causes the serious limitation of use in practical applications due to the material stacking, hydrophobicity and fabrication process complexity. In this work, a facile and effective plasma-assisted strategy is put forward to increase specific surface area, tune hierarchically porous structure and promote wettability of nitrogen-doped graphene fibers (NGFs), resulting in the improvement of electrochemical performance. The supercapacitor assembled from plasma-treated NGFs shows superior capacitance (878 mF/cm² at 0.1 mA/cm² current density) and high energy density (19.5 μW h/cm² at 40 mW/cm² power density), which is 23.7% and 131.4% higher than that of NGFs and GFs, respectively. Additionally, the fiber-based supercapacitor based on plasma-treated NGFs exhibits high rate capability of 59.8% and excellent cyclic performance (95.8% retention over 10,000 cycles). These plasma-treated NGFs can be promising candidates for high-performance and flexible power sources in future wearable electronics.     

Meticulously tailoring phase boundary in KNN-based ceramics to enhance piezoelectricity and temperature stability

Although KNN-based ceramics with high electrical properties are obtained through a variety of strategies, the temperature sensitivity is still one of the key technical bottlenecks hindering practical applications. Here, we use a new strategy, meticulously tailoring phase boundary, to refine the ferroelectric boundary of KNN-based ceramics, leading to high piezoelectricity companied with improving temperature stability. The highest d₃₃ value in this system reaches 501 pC/N with a T_C ∼ 240°C, whereas a large strain of ∼0.134% can be kept with 10% lower deterioration until 100°C. The origin of high piezoelectricity is mainly attributed to the well-preserved multiphase coexistence and the appearance of nanodomains, which greatly facilitate the polarization rotation. Instead of the changed intrinsic thermal insensitivity, the precision phase boundary engineering plays an important role in strengthening the temperature stability of electric-induced strain. This work provides a simple and effective method to obtain both high electrical properties and excellent thermal stability in KNN-based ceramics, which is expected to promote the practical applications in the future.     

Sea urchin-like LiAlO2@NiCoO2 hybrid composites with core-shell structure as high-performance Li storage materials

Sea urchin-like LiAlO₂@NiCoO₂ hybrid composites with core-shell structure assembled with nanoneedles have been successfully fabricated through a facile hydrothermal route followed by a calcination procedure in N₂ for the first time. The sea urchin-like architecture with large accessible surface can offer numerous active sites for redox reaction. The synergy of two advantages has dramatically improved the electrochemical behavior in terms of specific capacity, cycle performance and rate capability, especially at high current densities. The LiAlO₂(5.0 wt%)@NiCoO₂ displays charge capacities are 1309.0 and 933.6 mAh g^?1 at 0.5 and 1A g^?1, respectively, after 400 cycles. However, the charge capacities of bare NiCoO₂ are only 562.9 and 476.7 mAh g^?1 at corresponding rates. Especially, LiAlO₂(5.0 wt%)@NiCoO₂ preserves 358.1 mAh g^?1 after 500 cycles at 2A g^?1 with a capacity retention of 74%. The superior electrochemical property is related to the sea urchin-like nature and the ingenious composition design. In addition, the DFT calculation result shows that the formed stable, well-coordinated, and metallic interface between LiAlO₂ and NiCoO₂ are very helpful for reducing the interfacial impedance and beneficial for the improved rate capability of the materials. Therefore, such LiAlO₂@NiCoO₂ composites with unique morphology demonstrate a huge potential as electrode materials for Li-ion batteries.     

Research on the effects of surface modification of ceramic powder on cure performance during digital light processing (DLP)

Digital light processing (DLP) is one of the most important additive manufacture technologies to fabricate ceramic parts with complex geometries. Compared with pure photosensitive resin, the cure performance of ceramic suspensions is obviously different due to the optical property change after the addition of ceramic powders. In this paper, a unique oxidation process was used to modify the optical properties of nitride powders including AlN and Si₃N₄. The properties of oxidized ceramics were investigated and the cure performance of ceramic suspensions was then characterized. The effect of oxidation time on cure performance was evaluated. The results showed that for AlN, oxidation process leads to the smaller cure depth and smaller excess cure width as compared with non-oxidized AlN and for Si₃N₄, oxidation process leads to the larger cure depth and larger excess cure width as compared with non-oxidized Si₃N₄, indicating that both refractive index and light absorbance of ceramic powders have obvious effects on cure behaviors. Additionally, the cure behavior of oxidized ceramic suspension in this study shows that the relationship of cure depth vs. incident energy agrees well with Beer- Lambert model, but the excess cure width vs. incident energy is not consistent with quasi Beer-Lambert model due to the nature of digital micromirror device (DMD).